injection pressure
英 [ɪnˈdʒekʃn ˈpreʃə(r)]
美 [ɪnˈdʒekʃn ˈpreʃər]
n. 注射压力
双语例句
- The influences of injection pressure and injection temperature, two important injection parameters, were studied.
研究了注射压力和注射温度这两个重要的注射参数对注射坯体质量的影响。 - It is indicated that with the decrease of the injection pressure, the number of larger drops decreased, and the number of smaller drops increased, spray quality was improved evidently.
这说明随启喷压力的增大，大颗粒液滴有所减少，小颗粒的液滴增多，雾化质量有明显地改善。 - Therefore, using higher specific gravity and dynamic viscosity of biodiesel is able to decrease fuel injection pressure properly.
由此结果可知、比重和动力黏度较高的生质柴油，可适当的将燃料喷射压力减低是可行的。 - Theoretical result shows that even in a very low admixture injection pressure, fracturing will occur in surrounding soil.
理论分析发现即使在很小的固化剂注入压力作用下，周围土体也会发生劈裂现象。 - Process window analysis, another part of mold flow analysis, examines melt temperature, mold temperature, injection pressure, and fill times.
加工窗口分析、它零件的模流分析，检查熔体温度、具温度、塑压力和充填时间。 - Another benefit is the very short distance from the pot chamber to the nozzle, this means that very little injection pressure is lost during injection.
其另一个优点是从料仓到喷嘴的距离极短，这意味着在注塑过程中注射压力的损失极小。 - The results showed that Sauter Mean Diameter ( SMD) of biodiesel decreased, as the injection pressure increased and the orifice diameter diminished.
结果表明：随着启喷压力的增加和喷孔直径的减小，生物柴油索特平均直径不断减小； - The elongate frame under the station value is the primary injection pressure of the station, touch it to modify.
站位值下的长条框即为各站的一注压力，触此可进行修改。 - During the process of water injection production, high injection pressure cut in mudstone should be prevented to reduce casing damage.
油田开采过程中，应防止高压注入水进入泥岩，以预防和减少由于泥岩进水发生蠕变导致套管损坏。 - In the Common Rail accumulator injection system, the generation of the injection pressure is separate from the injection itself.
在共轨蓄压喷射系统，新一代的喷射压力是分开的，从注射本身。 - For researching crack initiation condition and water injection pressure needed, this paper built up a mechanics model of crack tip based on crisp fracture theory of compound crack.
为研究初始裂缝尖端起裂的条件和所需注水压力，依据断裂力学的复合型裂纹的脆性断裂理论，建立了裂缝尖端力学模型，给出了计算方法。 - CFD Analysis for Effect of Injection Pressure Fluctuation on Cavitating Flow in Diesel Engine Nozzle
喷油压力波动对喷嘴内空穴发展影响的CFD分析 - Aperture atomizer Experimental of effect of water mist nozzle injection pressure on fire extinguishing
喷孔式喷油嘴喷雾器细水雾喷头喷射压力影响灭火性能的实验 - Practices have proved that the upper injection pressure limit, determined with pseudopaisson's ratio method, based on passive microseismogram is suitable for oilfield development.
实践表明，以无源微地震测试结果为基础的拟泊松比法确定的注水压力上限能够较好地适应油田开发的需要。 - After one year, injection pressure dropped and apparent water injectivity index rose, and interbedded injectivity behavior was improved in the injection wells.
试验一年以后，水井注水压力下降，视吸水指数上升，层间吸水状况得到改善； - Injection pressure and holding pressure I.
注射压力和保压压力。 - In the paper, matching tests were made for different combustion chamber geometries, injection pressure levels and injection nozzle configurations in a6110 type diesel engine.
本文对燃烧室几何形状、喷油压力、喷嘴类型等进行了匹配试验。 - A constant volume cell for spray study was designed to investigate the thick spray characteristics under high injection pressure and high ambient pressure.
为了研究柴油机高喷射压力、高背景压力下的密集喷雾特性，自行设计了喷雾模拟试验装置。 - The durability of diesel engine fueled with rapeseed oil was tested after the fuel injection pressure improved and a fuel pre-heating device was installed.
在柴油机上提高喷油压力和加装燃油加热装置后，进行了燃用菜籽油的耐久性试验。 - Injection pressure should be set low initially and increased to the point of filling the part just short of causing flash.
一开始应设定低的射出压力以填充零件至刚好不会造成毛边。 - What is specific injection pressure?
什么是特殊注射压力？ - This study is undertaken to develop methods and technology of using the injection pressure waveform to diagnose, on-line the malfunctions of a diesel injection system.
本文以数值模拟的方法来探讨柴油引擎之喷射系统元件发生故障时，所表现出来的喷射压力波形特徵。 - Influence of the injection pressure to plastic mould core offset
注射压力对塑料模具型芯偏移量的影响 - The molder must recognize the dangers of excessive fill speed, insufficient injection pressure, excessive melt temperature, and inadequate packing.
注塑工必须认识过快填充速度、不足注塑压力、过高融化温度和不充分挤压的危害性。 - It can be found through oil field development process that oil well casings are more and more seriously damaged as oil field water injection pressure and stratum pressure are increased.
通过油田的开发历程可以看出，随着油田注水压力、地层压力的提高，套管损坏井越来越多。 - Anew forecasting method of wellhead injection pressure for polymer flooding is established based on Dupuit formula.
依据裘比公式建立了一种新的聚合物驱油井口注入压力预测方法。 - Experimental of effect of water mist nozzle injection pressure on fire extinguishing Can be used to decrease the dust, moisten the air.
细水雾喷头喷射压力影响灭火性能的实验具备喷雾降尘功能，适宜降尘，湿润空气。 - The high pertinence between the weight of injection molding products and injection pressure is unveiled by experiments and analyses.
通过实验和分析揭示了注塑机产品的件重和充填过程的压力之间有很强的相关性。 - The influences of injection pressure, gas temperature of cylinder and the diameter of nozzle hole on the spray characteristics were analyzed.
分析了喷射压力、缸内温度和喷孔直径对喷雾特性的影响。 - The injection pressure, injection velocity, the mold temperature and the plastic melt temperature are mainly investigated.
本文重点研究了注射压力、注射速度、模具温度以及熔体温度的影响。